Cost guide · Updated October 2026
How Much Does Insulation Cost?
Insulation is priced by area and type. Attic insulation is often the most cost-effective place to start.
Typical range
$498–$4,500National average
$1,852Source: HomeAdvisor, accessed October 2026. Actual prices depend on your home, materials and location.

Common prices
| Item | Typical cost | What it covers |
|---|---|---|
| Attic insulation | $1–$7 per sq. ft. | Installed |
| Wall insulation | $1–$4 per sq. ft. | Installed |
| Basement insulation | $1.50–$2.50 per sq. ft. | Installed |
| Blown-in project | $975–$2,200 | Project total |
| Fiberglass batts | $0.30–$1.50 per sq. ft. | Product only |
| Installer labor | $40–$80 per hour | Labor only |
What the labels mean: Installed materials and labor · Project total typical total for the whole job · Product only materials or the product itself, no installation · Labor only installation labor, no materials. Permits, removal of old materials and finishing work are included only where a row says so.
Example budgets
These examples show how the published figures add up for common projects. They are arithmetic on the national ranges above, not quotes.
Topping up a 1,000 sq. ft. attic with blown-in insulation
$975–$2,200Published range for a typical blown-in project.
Insulating 1,000 sq. ft. of existing walls
$1,000–$4,0001,000 sq. ft. × $1–$4 per sq. ft. Usually blown into the wall cavities through small holes.
Unfinished basement walls, 800 sq. ft.
$1,200–$2,000800 sq. ft. × $1.50–$2.50 per sq. ft.
Scope choices that change the price

- Batts, blown-in or spray foam. Batts are the least expensive and suit open framing. Blown-in fills irregular attics and closed walls. Spray foam costs more but also seals air leaks.
- Air sealing first. Sealing gaps around wires, pipes and attic hatches before adding insulation often makes the biggest difference in comfort.
What affects the price
- Area. Attics are usually easiest; finished walls are hardest to reach.
- Type. Batts are lowest cost; spray foam costs more and also seals air leaks.
- Removal. Old or damaged insulation may need to come out first.
- Air sealing. Sealing gaps before insulating adds cost but improves results.
Costs that are often left out
- Old insulation removal. Damaged, wet or pest-contaminated insulation may need to come out first.
- Ventilation. Attic vents must stay open. Baffles at the eaves keep insulation from blocking airflow.
- Knob-and-tube wiring. Older wiring may need to be evaluated by an electrician before insulation goes over it.
Upkeep after the job
- Check after roof leaks. Wet insulation loses much of its value. Replace it after leaks.
Questions to ask before you hire
- What R-value will I have after the work?
- Is air sealing included?
- Will you add baffles to keep attic vents clear?
- Do you need to remove old insulation first?
- Get at least three quotes. Prices for the same job often vary a lot between contractors.
- Compare the same scope. Make sure each quote covers the same materials, removal, permits and cleanup.
- Check license and insurance. Ask for proof of insurance and look up the contractor's license with your state.
- Get it in writing. A written estimate should list the work, the price, the payment schedule and the warranty.
Sources
- HomeAdvisor cost guide, accessed October 2026
- IRS: FAQs on changes to sections 25C and 25D
Prices are national figures published by the sources above and are for general information only. Example budgets multiply those published ranges by the quantities shown. They are not a quote or an offer from FixFinch or any contractor.
